Autel MaxiDiag MD808 Pro Review on Hyundai i30

Posted on June 13, 2019 by wp-admin

Model: Hyundai i30 year 2008 with 220,000 KM
Symptom:
Check engine light turns on and detected a P0420 fault code (P0420: Catalyst System Efficiency Below Threshold (Bank 1)).
I don’t feel anything wrong with the output or the engine. The lambda value was slightly higher in the second year overall test. This was also due to the end muffler corrosion.

First attempt (using cheap Bluetooth OBD dongle):

I checked the fault (or diagnosis) DTC code using Bluetooth OBD2 dongle bought last year. But I also learned that the code could not be read if it was not a fault in progress. I checked that the wheel and steering related trouble codes were floating in the ‘Comprehensive Certificate of Automobile Functions’ which I received after the inspection at the comprehensive inspection center, but I could not confirm it with the Bluetooth OBD2 code reader at all. I also used it on the Santa Fe CM. I found out that the parts were bad and sometimes I could not read the trouble code during normal operation.

As the day gets warmer, the body changes and the car becomes something different. The OBD2 Bluetooth scanner that I used was not able to find where it disappeared and I am expecting what the reason is, but I am afraid because I can not check it, and then I buy a proper one. I tried to buy a scanner with a screen-oriented text, and eventually, I decided to get a Autel diagnostic system.

Second attempt (using Autel MaxiDiag MD808):

Function:

It can be seen that the car which has been released recently has many functions required for setting.

The picture below is a picture that is connected with a PC, but it is the same when connecting with a vehicle using an OBD2 cable. If you connect the PC with USB or if the key is not connected to the car, turn it on when you connect it. If you turn the key off or ACC, connect the diagnostic to the car and then turn the key position to ON or start. No diagnostic code is generated. If you do not follow this, your C # code will generate C1623 code.

The function of each menu is …

SCAN : You can read and erase the fault code for each manufacturer, model, and model of a specific vehicle, or check the value output by the vehicle through OBD2.

SERVICE : Performs special functions supported by the scanner. Battery reset (BMS), oil change reset, steering angle sensor (SAS) reset, EPB (electronic parking brake) re-learning, diesel DPF function, throttle position sensor reset etc.

OBDII : Read and clear the fault codes of certain items, or check live data.

SETUP : You can select the setting of the diagnostic unit, the language, the unit, and the beep sound.

PLAY BACK : Play back live data saved during vehicle diagnosis.

UPDATE : After using the USB cable to update the device diagnostics, after the initial purchase, there was no corresponding menu, but this menu was created after plugging the MicroSD card into the PC or notebook reader, and from this time you do not have to plug the MicroSD card directly into the PC reader Directly updated via cable. You need to update immediately after purchase or periodically. The update seems to be quite a lot.

Diagnose:

First, select SCAN to select the sales region of the vehicle manufacturer. The same maker has different specifications and models depending on the region in which they are sold. To choose a Hyundai that sells to Korea, you have to choose Asian. You have to choose USA to choose Hyundai which is sold to the US.

If you choose Asia, Asian car makers will pop up and use arrow keys to select.

Read the data …

and select the vehicle. It seems that automatic selection is not possible … Select it manually.

Select the vehicle production area and select the

vehicle model.

Select model year

Select engine type

When Auto Scan is selected, the vehicle is scanned as a whole and the fault code is output if there is a fault.

If you select Control Units without Auto Scan, you can scan each device.
So I scanned my 2008 i30 (FD) 2.0 model and it shows up.

It is a diagnostic code related to steering or VDC. I suppose that it was the maintenance of the lower body at the key ON state anyway.

The picture above shows the live data saved and played back. Of course, you can connect to the vehicle to check in real time … You can also save, you can also play the picture as shown below. Saved data can be sent to PC in text form after connecting with PC.

Various diagnostic information can also be moved (output) to PC.

The waveform can be seen roughly, but it is a bit questionable whether it is output correctly. The sampling rate seems to be too low.

First of all, I erased all fault codes diagnosed to my car i30 …. I drove for about 2 weeks.

The P0420 does not disappear, it is erasing even if erased, and the fault codes related to steering or VDC no longer display.

I will use the Autel MD808 Pro scanner for a while and use it with confidence.

How to change language and update Autel Scanner

Posted on June 1, 2019 by wp-admin

1.First of all, the language of the Android Tablet need to change from Spanish to English.
Double check System　setting —- language —-English

2.The language of Diagnostic need to change.
To change the language from Spanish to English.

Step 1: Click at Maxisys.

Step 2: Click at “Settings”.

Step 3: Click at “ Language”

Step 4: Select “ English”

Then you can see that the language is in English now.

After changing language to English and if you found it is blank here(Maxisys—Diagnostic).

Please go to Update and select vehicles software and reload them.

the video of How to change language and update Autel Maxisys

How to update Autel MaxiSys Pro MS908P One Year Update Service

Posted on May 29, 2019 by wp-admin

Autel Maxisys Pro MS908P can diagnose more than 80 US, Asian and European vehicle coverage for codes, live data, actuation tests, adaptations, coding and ECU programming Displays live data in text.

it is one year free update, after expired, how to update?

buy the update serivce from here: Autel MaxiSys Pro MS908P One Year Update Service

How to make it work?

Register all your Autel tools to your free Autel ID account at autel.com to download FREE software updates regularly to keep your Autel tools functioning like brand new.

Constantly Update Autel Maxisys for Current Vehicle Coverage
Register Tool After Purchase for 1YR FREE Software Updates

Where do i find the activation code?
check setting-about-and find the activation code here:

To Redeem on your MS908P:

1. Sign in to your Autel account at Autel official website
2. Select Redeem on the left
3. Select the product
4. Peel off table & enter Activation Code
5. Press OK Button to confirm

Finally, wow, instantaneous access to the new updates!

Inexpensive Diag Scanners for 1998 1999 Mercedes with 38 Pin Connector

Posted on May 21, 2019 by wp-admin

Topic:

looking for an inexpensive diagnostic scanner to troubleshoot a 1999 E430 W210
(as well as other older Mercedes models with 38-PIN round diagnostic socket).

Working experience:
I recently purchased an Autel MD808 PRO under the belief that it could, among other things, clear the “Service Engine Soon” instrument cluster readout on any Mercedes with OBD II. Per Autel Tech Department it can clear codes/instrument cluster readouts through the OBDII port…but only for years ’08 and newer, which I (frustratingly) discovered AFTER I had purchased and attempted to use it.

I saw there is a “Autel 38 Pin OBD2 Diagnostic Scanner Adapter Connector Cable for Mercedes Benz” their own product. So i want to find out if it will work with the DS808 Pro in all claimed capabilities.
It’s confirmed. There is no way to interface the 38 pin connector to the OBD II 16-pin connector with an “inexpensive” Autel scanner.
According to said tech department, there is NO ADAPTER that can be used to interface the MD808 Pro to the 38-pin connector. For that matter, the technician intimated that the tool that Autel produced that COULD interface and clear the instrument cluster readout was a >$4K model. That’s way to expensive for me.
The technician further explained that the ’99 Mercedes was a little ahead of its time, having BOTH the 38-pin connector found under the hood in the fuse box and the OBD II port under the dash. From what I understand, the OBD II port will allow the reading of ENGINE-specific data…but just about any inexpensive OBD II scanner can do that.
If there is an inexpensive scanner that can read ALL the data/systems AND clear the instrument cluster readouts, I would be interested in hearing about it/them.

Obd2tool.com recommendation:
Anyone who buys those $4 to $10 OBD2 to 38-pin adapter cables and expect to access all the modules is dreaming.
You need Mercedes special diagnostic scan tools.

1). Foxwell NT520 with Benz software pre-loaded + 38 PIN connector
(Price: less than $200 with 38-pin adapter)

This 38-PIN multiplexer adapter allows you to connect your Mercedes equipped with the older, round 38 PIN connector to a compatible Foxwell NT520 PRO diagnostic tool.

Foxwell NT644 Pro and GT80 with 38-PIN adapter certainly will do, but they are out of price range.

foxwell-benz-38-pin-cable-2
foxwell-benz-38-pin-cable-1

NT520 Pro Mercedes Benz model list:
A Class: 168 , 169 , 176
AMG GT: 190
B Class: 245 , 242/246
C Class: 202*(As of 06/97), 203 , 204 , 205
CL Class: 140*, 215 , 216
CLA Class: 117
CLC Class: 203
CLK Class: 208*, 209
CLS Class: 218 , 219
E Class: 210*(As of 03/97), 207 , 211 , 212
G Class: 461 , 463
GL Class: 164 , 168 , 166
GLA Class: 156
GLC Class: 253
GLE Class: 292, 166
GLK Class: 204
M Class: 163 , 164 , 166 , 292
Maybach Class: 240
R Class: 251
S Class: 140*, 220 , 221 , 222 , 217
SL Class: 129*(As of 09/99), 230 , 231
SLC Class : 172
SLK Class: 170(up to 2001)*, 170(after 2001) , R 171 , R 172
SLS Class: 197
SLR Class: Series 199

2). MB star Compact C4/Mercedes BENZ C5
If you want to access ALL the modules for your car, a MB Star C3 /C4/C5 clone is a way to go.
All MB SD control units are accessible, like engine ECU, ABS, Airbags, SRS, Aircon, Immobilizer, Keyless Entry and the rest of 40+ control units used in MB cars. You can Read / Delete Faults, Live Data, perform sensor actuation, read current configuration, initialization and a lot more.

All MB from late 80’s to 99 = HHT-WIN
All MB from 2001 to 2009 = DAS
All MB from 2010+ = Xentry
The latest MB star diagnostic system is compatible with HHT-WIN software for old Mercedes troubleshooting.

Related article: HHT-WIN Manual: Vehicles & Modules Support, SW Install, Reviews

3).
Some people use Delphi system for old Mercedes. i.e I use it on a 1998 E320, and I can access Engine computer, Transmission Control Unit, Instrument Cluster, Restraint System, Ignition (EIS), Climate Control, ABS/BAS, but it will not read body control modules, like SAM, PSE, door control modules, lower/upper console modules etc. This is good enough for me.
If you need the delphin system, please contact us via PM.
Disclaimer:
Parts of Mercedes owners prefer icarsoft scanners. iCarsoft MB II is the fact that it will not work on older models past 1993. It will not work on models that require a 38 pin connector such as the E 320 and CLK 430. In these models it can only read the ECU (check engine light). You also want to skip MB i980 which can only do ECU and SRS / Airbag diagnostic.

Autel Maxisys MS906BT Professional Car Diagnostic Tool (Upgraded Version of MS906)

Posted on April 8, 2019 by wp-admin

AUTEL MaxiSYS MS906BT is one of the best Profesional Automotive Diagnostic Tools in the market for technicians and professional mechanics.

In this review, I will provide you with the most details about this Autel Scanner.

Autel Maxisys MS906BT Overview

The Autel Maxisys MS906BT and MaxiSYS MS906 have the same OBD scanning and testing capabilities. They both support reading/clearing codes, live data, actuation tests, ECU coding, and adaptations. Plus they look a whole lot similar in physical appearance.

However, the latter just gets the edge over its predecessor in terms of overall functionality. For instance, it can connect to a car’s OBD system using VCI. That is a wireless connection which basically allows you higher mobility.

There’s the option of adding an inspection camera to the scanner. The camera doesn’t come with the default package though, it is sold separately. Here are more unique features that you will get from the Maxisys MS906BT.

Autel MS906BT Detailed Review

Android OS

The scanner runs on an open-source Android operating system (OS). It also features a powerful Exynos 6-core processor with amazing multitasking abilities. That is why it is very fast to boot up and run scans/tests.

Full-Service Scanner

You can use this scan tool for all OE-level OBD2 diagnostic tasks. That includes reading/erasing codes, live data, freeze frame data, active tests, ECU information, matching, adaptation, data logging, ABS Bleeding, Oil Reset, TPMS Programming, and so much more. The Smart AutoVIN technology makes it so easy to identify a car.
Extensive vehicle coverage

As one of the leading professional automotive diagnostic scanners, the MS906BT is compatible with so many car makes and models. You can use it on over 80 brands of US, EU and Asian-made car models with OBD2 systems.

Advanced user support

The comprehensive help and support you get when using the Maxisys MS906BT is yet another reason why it qualifies as one of the best professional automotive diagnostic scanners.

Fitted with a Wi-Fi module, you can go online to browse for verified diagnostic and repair tips for any vehicle. Even better, the MaxiFix community (used by Autel customers) is a great platform for getting proven fixes and recommended parts.

In case you need further assistance you can reach the manufacturer directly using interactive data logging. They will give you troubleshooting, diagnostic and repair guidance to help you get any job done.

Superb construction

First things first, the MS906BT is well-sized for portability. It measures 25.6 x 16.7 x 7.4 inches and weighs 19.25 pounds. Not so different from a tablet.

As a matter of fact, the 7-inch LED touchscreen will leave you feeling like you are using an ordinary tablet. The 1024 x 768 resolution displays images with unmatched clarity.

Besides that, the built-in lithium-polymer battery allows you up to 14 hours of continuous use without charging. That is a lot more time than you will get in other professional automotive diagnostic scanners.

Finally, the scanner supports USB connection and also features audio and auxiliary connectivity ports.

Who is it built for?

A brief look at the Maxisys MS906BT’s features will automatically tell you it fits among professional automotive diagnostic scanners. The fast speed, multitasking capabilities, database for organizing customer/vehicle data and advanced functionality make this scan tool ideal for professionals who offer auto services.

Autel Ms906BT vs MS906 vs MS908 Comparison Chart

Mercedes Increase Speed Limit by Autel MaxiSys Pro MS908P

Posted on April 5, 2019 by wp-admin

How to reprogram Mercedes Benz C240 to remove the speed governor that is set at 250k/h (from original 130 km/h).

Requirement:

Autel Maxisys Pro MS908P

Autel MaxiFlash Elite J2534

Steps:

Connect MS908P and J2534 with Benz C240.

Go to “MaxiSys-> Diagnostics-> Benz-> vehicle detect”.

Gateway data initializing…

Get the VIN number. Tap OK to go on.

Select the date of manufacture vehicle. This case is up to 2003.

Press the button left to select left-hand steering.

System data initializing…

Communication is established…

Go to Programming/Coding.

Go to ME2-SFI-Motor electronics 2.

Establishing communication…

Go to Variant coding.

Go to Display of coding data.

Go to Coding.

System data initializing…

Scroll to 2031 about speed limit. Put on the bar.

Tap F2 Edit.

Set 250 km/h, and tap OK.

Tap F3 send.

Tap OK to make sure that the coding is transferred to the control unit.

The coding has been carried out.

Turn off the key and then turn the car back on. Then you can go for a drive.

Ps. cool thing!!

Go to instrument cluster.

Establishing communication…

Go to Active Test.

Go to Actuation of the instrument pointer up to the maximum position. And you will see

End!!

What Autel Maxisys MS906 Scanner Is For

Posted on April 1, 2019 by wp-admin

No doubt, its not a gadget to keep at home and show-off. Its
designed for the professionals and repairing shops. More precisely, for
large rebuilding houses.

The price of the product is quite high and even small vehicle garages will find it hard to afford.

It is intended for mid-scale or large-scale service providers.

It can diagnose tens of vehicles per hour depending on your activeness.

I admit Autel MaxiSYS MS906 is costly but comparing to the value it provides; I must say it a reasonably priced product. Moreover, don’t consider it as an expense but
an investment as it can cut the time for closing a deal by half. That
only means more business for you but with lesser stress.

Conclusion

Conclusively speaking, Autel OBD2 Scanner
MaxiSYS MS906 Automotive Diagnostic Scanner happens to be the perfect
device for significant repairing houses out there. I strongly recommend
the device for its high-quality performance standards. Also remember the
other versions after it, the ms906bt and ms906st.

I doubt that you will ever love to use any other device if you
experience this one. I am personally a fan of the device and the Autel
Brand itself.

Moreover, it is backed up by the prestige of the Autel Brand. Autel
is a great manufacturer who always strives for presenting the best and
eliminating the difficulties of its customers. In case, you encounter
with some problems for using the device or if it doesn’t function well,
although that’s pretty rare, an Autel representative will help you out
and resolve your issues. Just contact https://www.obd2tool.com/ customer support.

Autel MaxiCOM MK908P VS MaxiSYS MS908P

Posted on March 25, 2019 by wp-admin

Question: Should I buy an Autel MK908P instead of Autel MS908P?

Answer: Autel MK908P is much better in hardware. Will run faster and much more stable.

Pls read the chart for details

Autel maxisys elite FAQ

Posted on December 19, 2018 by wp-admin

Question: Does the Maxisys Elite scanner comes with troubleshooting feature?
Answer: Yes, it does. The Autel maxisys elite diagnostic scanner can diagnose vehicles, read and clear DTCs. Also, it can do ECU coding and programming. As a matter of fact, the maxisys elite scanner is one of the most advanced tools on the market with a wide range of outstanding features. It can used on the different car make and performs all OBD2 functions.

Question: Can I use this Autel Scanner to calibrate seat sensors?
Answer: Of course, you can. This Autel maxisys elite scanner can do on most cars. But before you buy it, get in touch with Autel and find out if it’s compatible with your car make or model. Some users have reported compatibility problems and you don’t want to be one of them.

Question: How important is the freeze-frame feature in a diagnostic scanner?
Answer: This is a standard feature built into all OBD2 systems that normally takes a snapshot of data when an emissions-related diagnostic trouble code sets. By default, there are some scanners that may only retrieve one frame of captured data on demand. But some manufacturers build in expanded freeze-frame data capture routines that show more than a standard frame. In order to pull this expanded data, it normally needs a scanner with expanded freeze-frame retrieval capabilities or an original equipment diagnostic scanner.

The MaxiSYS MS908SP Pro is now our most powerful diagnostic scan tool.

Posted on November 21, 2018 by wp-admin

Descripiton:
Same Features as MS908S PRO
Includes New Smaller MaxiFlash Elite J2534 Device
Perform Pass-Thru Programming Features
J2534 Device Includes Internal Bluetooth VCI

It features a 9.7” LED capacitive touchscreen and upgraded, top-of-the-line hardware.
The Autel Scanner MS908S Pro is one of our most advanced tablet scanners available, with a hexa-core processor, double the memory at 64G, better quality 8MP camera, and 2 USB ports.

Product Info:
9.7” Color Touchscreen
1.3GHz + 1.7GHz Hexa-Core Processor
64GB SSD Memory / 2GB RAM
11,000mAh Lithium-polymer Battery
OBDII Connector Kit & Carry Case
MaxiFlash Elite J2534 Programming Device
Android 4.4.2 / WiFi Update & Print via PC
MaxiSYS Suite Applications:
MaxiFIX / Shop Manager / Remote Support
1Yr FREE Software / 1Yr Warranty
8MP Camera with Flashlight
2 USB Ports
AutoVIN/ AutoSCAN
Covers Domestic, Asian and European
Vehicle Manufacturers (1996 to Present)
Access Repair Records & Test Data
Reset Diesel Emissions Light/Med. Duty
15+ Service Reset Features
Access All Modules in All Systems
Bi-Directional Control
Advanced Coding & Adaptations
Key Programming Domestic & Asian 2001+
Kit Consists of: MS908SP Pro Tablet, MaxiFlash Elite, USB Cable, Charging Cord, Connector Kit, AC/DC Adaptor, User Manual and Carry Case

MaxiSYS Pro Diagnostic Scan Tool System (MS908SP) by OBD2TOOL. If you’re looking for a reliable solution to complete your project, this 1st-grade product is right up your alley. Designed utilizing the finest materials, it delivers unmatched levels of durability and strength needed to provide long-lasting service life. Superior in functionality, it will help you make any job easier and faster.