CONDOR XC-MINI PLUS II Tutorial: How to Duplicate Mul-T-Lock Dimple Key

In the last article, I introduced how to engrave on a key blank by using Xhorse Condor XC Mini Plus II. Today, I’ll show the steps of cutting Mul-T-Lock dimple key household key.

Preparation:
Original key
Blank key
Cylinder
1.0mm probe
Dimple cutter (internal)
Dimple cutter (external)
M5 clamp
CONDOR XC-MINI PLUSⅡ

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-1
How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-2

Step-by-step guide:

Step 1: Height calibration

Stick in the probe and the dimple cutter (internal)

Make sure the clamp is tightened

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-3

Hit Settings>> Device Calibration>> height calibration>> Start

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-4

Tips: Install M5 clamp then select A position A is upwards and tighten left, don’t insert key blank

Height calibration complete

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-5

Step 2: Key learning

Select Household>> All regions>> Mul-T-Lock (8.8mm-R)>> Mul-T-Lock 4-4

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-6
How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-7

Insert the original key

Hit ‘Decode key’ to start the key learning

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-8
How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-9
Household key learning completed

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-10
How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-11
How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-12

Step 3: Key cutting

Insert the blank key and close the cover

Hit ‘Start cutting’>> OK

After cutting, clean the shavings and remove the key

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-13

Tighten the clamp and install the dimple cutter (external)

Repeat height calibration again

Select Dimple (external)>> probe and cutter setting>> ∅ 6*100* dimple (external)>> Save

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-14

It will prompt ‘Machine parameter modify successfully, perform height level adjustment’.

Click OK>> Start

Calibrate the height again

Insert the key and start to cut the external cuts

Click OK>> Start cutting

Cut one side of the key successfully, then flip the key to cut another side

Key cutting is completed

Finally, insert the key into the cylinder to test

How-to-Duplicate-Mul-T-Lock-Dimple-Key-CONDOR-XC-MINI-PLUS-II-15

Done!