Porsche PIWIS II Tester Automatic Coding for Porsche Macan

Here comes the step-by-steps guide on how to use Porsche II tester to perform “Automatic Coding” for Porsche Macan.

Preparations:

Porsche PIWIS 2 V18.15 V17.500 Free Download

How to Install/Restore Porsche PIWIS 18.100 Universal Image

Procedures:

Connect the Porsche Piwis2 to Porsche Macan,and then run the PIWIS II diagnostic software.

Select “DIAGNOSTICS”à”Macan”
Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-1

Loading control unit selection…

Starting diagnostic application,please wait…

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-2

Here I select “Gatewag”,”DME”,”Transmission control”,then click “Coding adaptions”

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-3

Changing display,please wait…

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-4

Information:Campaigns are stored for this vehicle in the PIWIS information system.

Please check the following VIN:*****************

See information,continue with [F12]

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-5

Click “Automatic coding”,then click [F12] to continue
Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-6

Coding in progress,please wait…
Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-7

Coding has been completed successfully.Press [F12] to continue.

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-8

Done!Now you can click “Overview” to check the control units status.

Porsche-II-Tester-Automatic-Coding-for-Porsche-Macan-9

 

VXDIAG Porsche Piwis3 Developer Mode shell config. update tips

The Developer Mode in Porsche Piwis 3 is not available when you update the shell, coz you lose the menu diagnostics configuration to switch between regular and developer mode,
Problem solved if you copy the old file com.porsche.piwis.Shell.exe.config

Here is how to update the shell config. and get the diagnostic configuration boxes back, on the system tab.

After a successful update from 37.250.20 you will loose the two above mentioned boxes from the System tab.
If you did not loose them, then the [PIDT] diagnostic software did not update completely.
So it’s a good thing to loose it !

Go to C:\PiwisApps\Shel\ and carefuly edit with notepad   this file –> com.porsche.piwis.Shell.exe.config

after the update the PIDT section shows up in green, after U edit it it will be blue.

First picture shows, red underlined, 2 places, beginning and the end of the green section, what to remove.
On top [Line 568 on mine] U delete  these four symbols       !–<     on the bottom [line 603 on mine] U delete these 3 symbols   –>
Then U save the config file.
Restart the PC and your Diagnostic config box for 991,981,970 and Diagnostic config for other models RE-APPEAR.

rm996 has the solution how get the developer functionality back up and running, !!! PM him.

[Similar solution for the lost with the Update Wiring Diagrams ]

VXDIAG-Porsche-Piwis3-Developer-Mode-1

Another tip might help you also.

It’s how to enable Developer Mode for Piwis 3

Developer mode is a special Piwis program that allow a lot of advanced coding normally reserved only to Factory.

With this function you will have a tool that can do more than software of official Porsche Dealer.
For example, you can reprogram all ECUs completely offline.

How to use Piwis Developer Mode:

Install winrar and winhex on your computer.

-1-locate the file c:\program files\porsche\PIDT_P_MIG_DLSS3\pidt\plugins\de.dsa.pidt.datatype.jar and copy it on your desktop in order to modify it.

Open it with winrar,in the wirar windows locate the file

\de\dsa\pidt\datatypes\utils\Helper$1.class and drag it on your destop , delete it from the archive after the copy, keep the winrar window open.

Open Helper$1.class on your desktop with winhex and goto offset E81, replace 9A by A7 and save.

Drag back the save file on the winrar windows still open and click OK.Close winrar

Copy the new file de.dsa.pidt.datatype.jar you just made in

c:\program files\porsche\PIDT_P_MIG_DLSS3\pidt\plugins, overwrite it.

copy the file aftersales.sig on your desktop and rename it development.sig.Copy this file back in the folder

Do exactly the same method given above with the folder c:\program files\porsche\PIDT_P_MIG_DLSS3 with its own files.

To transform it in developer :

Settings

Diagnostic configuration

981-991, mode, operating mode, E= development, P= production, V= aftersales ( regular piwis)

Other models line, mode, operating mode, E= development, P= production, V= aftersales ( regular piwis)

This method to switch between regular and developer works only with my backup and will not work anymore after

an update.

Images:
VXDIAG-Porsche-Piwis3-Developer-Mode-2
VXDIAG-Porsche-Piwis3-Developer-Mode-3
VXDIAG-Porsche-Piwis3-Developer-Mode-4

Maybe this helps Folks some.

Porsche PIWIS 3 Keygen Download Free + How to use

Free download keygen for VXDIAG Porsche Piwis III

https://mega.nz/#!CUYUlKYR!v9qgglhkXClmKizrVfCm3a33tId3wu1QS7LOvgxYQ1Y

Big thanks to Damien

How do you use the keygen:

This is the method you can try:

Make sure PIWIS is closed.  If it is open, right-click the Taskbar, and run Task Manager.  Select co.porsche.piwis.shell and End Task.

Click Start (WinKey) and type services.msc in the search box. Run services.msc. If the service is running, stop it.

If the Keygen is on the laptop, run it, and leave it open.

Run a Command Prompt.
At the Command Prompt, type:
WMIC BIOS GET SERIALNUMBER

Enter the Serial Number into the Keygen.
Enter the Country into the Keygen.
Change the Expiry Date to 01/01/2030.
The Dealer number is not important, but you can enter one if you know it (7 digit number).
Leave the Challenge Key blank for now.

Click Start (WinKey) and type services.msc in the search box.  Run services.msc
Change the AdminService startup to Automatic, and click Apply.
Click Start to start the service.

Run Piwis3.
Go to the Imprint section.
Enter 4 random digits into the Licence key boxes.
Tick the Accept box, and click License Update – it will say Not Valid – click OK.
Click Licence update twice more and OK.
The Request Key should have disappeared, and the Create Key button should be active – click it.
Place the mouse pointer at the bottom of the screen, and open the Keygen.
Enter the Request Key into the Challenge Key box, and click Generate.
Enter the licence key shown into the boxes on Piwis.  Tick the Accept box and click Licence update.
If successful, you should get a message to reboot.  Click OK, and the computer will shut down.

IMPORTANT!!

After starting the computer, open services.msc again.
Stop AdminService, set startup to Disabled.  You can now run Piwis.

You can also get the serial number by printing out the imprint request.
The snag with that is if you are imprinting a VM, it does not show the complete number.

(Credits to 911Turbo for his great contribution)

This is for your information.
If you don’t have a working PIWIS 3 program or the keygen is not working for you,
you’d better choose decent Piwis 3 software, tested version better

The circuit diagram in version 37.900 works perfectly even without online access. And whether the updates work now or not is only secondary, the main thing we have to play.

porsche-piwis-3-37900-download-1 porsche-piwis-3-37900-download-2

porsche-piwis-3-37900-download-3 porsche-piwis-3-37900-download-4 porsche-piwis-3-37900-download-5 porsche-piwis-3-37900-download-6 porsche-piwis-3-37900-download-7

porsche-piwis-3-37900-download-8 porsche-piwis-3-37900-download-9

How to Set Up Piwis 2 WIFI Configuration

Wifi PIWIS II is Samtec hardware support wireless connection for Porsche Piwis tester 2 diagnosis function. The client needs Porsche Piwis tester 2 Scanner wifi configuration after-sales service usual. Below Obd2tool.com share how to set up Wifi Piwis Tester 2.

Wifi Piwis 2 For Porsche Piwis Tester 2 Scanner Wifi Samtec Piwis 2 Hardware

How-to-Set-Up-Piwis-2-WIFI-Configuration-1

Wifi Porsche Piwis tester 2 Client Request:

I buy a Piwis 2 for Porsche diagnostic & programming, but I don’t know how to set up the wireless configuration. Some client bought wifi Piwis tester 2 for Porsche diagnosis, need help for wifi set up.

Wifi Piwis Tester 2 Wireless Configuration Guide:

First of all, need check the Rounter configuration, get the router id and password can set up by customer self.

Secondly, connect Piwis 2 to Laptop via USB cable, connect power adapter as well

Then, Check Setting as following show

How-to-Set-Up-Piwis-2-WIFI-Configuration-2

The fourth step: click & enter the “VCI configuration”

How-to-Set-Up-Piwis-2-WIFI-Configuration-3

And then, enter the Porsche Piwis 2 WIFI account into SSID blank, and password into WEP blank, then save the setting.

How-to-Set-Up-Piwis-2-WIFI-Configuration-4

Furthermore, back to Restart the Setting – Network Setting

How-to-Set-Up-Piwis-2-WIFI-Configuration-5

Then, choose WLAN, then check Search, then will search wifi information automatically

How-to-Set-Up-Piwis-2-WIFI-Configuration-6

enter the WIFI password as following, then choose Save.

How-to-Set-Up-Piwis-2-WIFI-Configuration-7

Finally, Wifi configuration all ok, it will display the Wifi

How-to-Set-Up-Piwis-2-WIFI-Configuration-8

Wifi Piwis2 Samtec hardware with V18.150.500 Piwis 2 software wifi setup guide as above. Any customer need purchase Piwis2 Samtec hardware or WIFI Piwis2 just let OBD2TOOL know freely.

Piwis 2 For Porsche Scanner Diagnostic Application Guide

Piwis 2 for Porsche Scan Tool with V18.150.500 Piwis Tester 2 diagnostic software support diagnostic for Porsche till 2017. How to use the Porsche Piwis Tester II for Porsche diagnostic function?

Obd2tool.com Share Piwis Tester 2 Diagnostic Application Guide as follows:

Selecting Piwis 2 Basic Application Mode and Defining Other Settings:

1. First set the corresponding basic application mode (Standard mode, View mode, Simulation mode) as well as all other parameters by means of the control application.

Selecting the model range:

First, you must select a valid model range. This is selected in the PORSCHE basic system before starting the diagnostic application. After starting the Piwis 2 basic system, you can select the corresponding vehicle model ranges under the menu item Diagnosis. The diagnostic application is then started with the data of the selected model range.

Please refer to the corresponding documentation for information on operating the PORSCHE basic system. The following steps describe the basis procedure.

Piwis-2-for-Porsche-PIWIS-tester-II-software-scanner-1

2. Secondly, we can start the basic system. The general interface is displayed where you can make basic settings.

3. Select the corresponding model range under the menu item Diagnosis. As an example, the Cayenne model range was selected here:

Piwis-2-for-Porsche-PIWIS-tester-II-software-scanner-2

4. Application start with the data valid for this model range r selection of the model range,.

Piwis II diagnostic application can be continue to do Piwis tester 2 for Porsche scan tool diagnosis detail.

Customer need purchase the Piwis 2 Porsche Diagnostic Software V18.150.500 Porsche Piwis II Porsche Scanners just contact us freely.

Possible to get Piwis 3 program work with Piwis interface tester 2

This answer for the question whether Piwis 3 diagnostic program can work with Piwis interface tester II

It may be an interesting subject, I’m sure there is some information about this out here.
The Piwis 2 interface is a lot more robust piece of equipment, compared to the cheesy and flimsy looking and feeling interface produced by Actia for Piwis 3.
Originally designed for the VW ODIS system,  the VAS 6154 VCI is quite the service needy piece. [Breaks easily] not a hard comparison to make.
Porsche went cheap on this VCI for Piwis 3. [my humble opinion, way below Porsche standard!]

There is a service from Poland and Ukraine [If I remember correctly] that can make the Samtec based Piwis 2 VCI,  to work with Piwis 3, unfortunately their charges are just as much and frankly cost prohibitive as the New Piwis 3 VCI.  2-3-4 thousand  dollars for these VCIs is simply not reasonable for small  operators. They will come down in price just like the Chinese VCIs did for all manufacturers as the markets get saturated and folks are not buying them as eagerly as in the beginning of the Piwis 3 phad.
They will get as much money as the market bares. [as much as people are willing to pay]

Your more pointed answers will not come in this tread Ibi.
This is CarsFan’s money making tread, he will not volunteer any information, but if U start your own tread, U may be more likely to find out stuff.

Regards, Albert.

p.s. links

Porsche piwis 2 china clone:

https://www.obd2tool.com/goods-4779-Porsche+Piwis+Tester+II+with+CF30+Laptop+or+Lenovo+E49AL+Laptop.html

Vxdiag Prosche piwis 3:

https://www.obd2tool.com/goods-10074-VXDIAG-VCX-DoIP-Porsche-Tester-Piwis-III-with-Lenovo-T440P-Laptop.html

porsche-piwis-tester-iii-download-1 porsche-piwis-tester-iii-download-2 porsche-piwis-tester-iii-download-3 porsche-piwis-tester-iii-download-4 porsche-piwis-tester-iii-download-5

PIWIS III Developer

Porsche Tester III opens the box and the CF54 computer is on.
The PIWIS-III diagnostic system is starting up.

PIWIS-III-Developer-1

PIWIS-III how to switch the developer mode

PIWIS-III-Developer-2

Select the system

PIWIS-III-Developer-3

Some models selected: 991,981,918,970, Cayenne \ Macan, select the rest of the new models: the other models series diagnostic configuration

PIWIS-III-Developer-4

Select mode

PIWIS-III-Developer-5

Select the operating mode

PIWIS-III-Developer-6

E: Developer mode P: Production mode V: Maintenance diagnostic mode(Can not choose P)
Select E mode

PIWIS-III-Developer-7

F8 save, the upper left corner shows the success of the save. Can exit.
Select the home page, select the diagnosis, and now the developer mode.

PIWIS-III-Developer-8
PIWIS-III-Developer-9

www.obd2tool.com

PIWIS Tester II is fully operational diagnostic equipment

Porsche Piwis Tester 2 is fully operational diagnostic equipment based on PIWIS vehicle interface and Porsche software. PIWIS II provides exclusive support for Panamera, Cayenne 92A, and all 2011 model range and above also provides legacy support for older models.
7-1

PIWIS II main functions
* General ECU diagnostics (DTC read/clear)
* Guided fault finding
* ECU programming/coding
* Real-time control parameters display
* Electrical schematics mapping

7-2

One year limited warranty and free update, registration support

PIWIS Tester II advantages
* Exclusive support for 2011 model range and above (Panamera,Cayenne 92A)
* Fast and stable connection
* Simulation mode (diagnostic session without VCI connection)
* End user capable DVD update
* Wired USB connection or wireless Wi-Fi connection

7-3

PIWIS Tester II equipment set includes
* Panasonic CF30 or CF31 notebook
* PIWIS II adapter (with Wi-Fi module)
* OBD and USB cables
* Laptop power adapter
* Preinstalled software

7-4

To purchase the equipment, as well as consulting, maintenance,please contact us:
Url: https://www.obd2tool.com
Email: sales@obd2tool.com

PIWIS II tool now for sale

After surfing the net looking for some goodies for my ’06 C4 I cam across Porsche Piwis Tester II. This company Obd2tool.com is selling the PIWIS II system, it has offline and online functions, to support ONLINE function, valid certificate must be available for Porsche Piwis Tester II.

Additional settings enabled for TPMS system with a borrowed gray market PIWIS. My 2006 C2S did not come with the TPM option. The hardest part of the retrofit was manually running wires as the wires were not in the front and rear main harnesses in my car. Then it needed programming with PIWIS to activate.

The biggest difference with the track tire settings is you define the target pressures. The other settings are predefined base on summer vs winter, 18 vs 19, partial vs full load. Not positive but I think the size option was also enabled.

The “Track Tire” is the special setting. There is an option in car diagnostic scanner PIWIS to rename it to whatever you want. My OCD struggled with “Track Tyre” to match the other settings or “Track Tire” as it’s properly spelled where I live. I settled on the latter

2-1

2-2

How to disable Porsche 911 DRLs with Porsche PIWS2 Tester 2

Daytime Running lights (DRLs) sometimes are annoying. Professional Porsche OBD diagnostic software dealers are possible to disable them.

Hardware options:

Porsche PIWS2 Tester 2 V18.1 diagnostic system

AllScanner VXDIAG VCX-PLUS PIWS2 tester 2 V18.1 diagnostic tool

VXDIAG multi diagnostic tool for Porsche PIWS2 Tester

NOTE:
The function is only available in countries where daytime running lights are not mandatory. Look up the Porsche menu and confirm it has the DRLs disable option, In USA, daytime running lights are not mandatory while in some other countries like German Daytime running light does not.
12-1
Instruction:

1)Setting the daytime running lights

Make sure the vehicle is in stationary or moving at walking speed when change the “Daytime Run Lights” function.

The dimmed headlights will always illuminate when the engine is running which indicates that the “Daytime Run. Lights” function is active.

This applies regardless of the light switch setting. The lighting for the instruments and switches is still switched on and off using the light switch regardless of the “Daytime Run. Lights” setting.

2) Install PIWS2 TESTER 2 software

Check obd2tool.com webpage to follow the Piwis tester 2 setup and software installation video instructions.

3) Click “INFO” Tab.

Hit “OPTION” button or click the icon of the same name in the deader

Select “Individual memory” option

Select “Light”

There are two options, activate and deactivate. Select “Daytime Run. Lights” to Deactivate().