How to Configure WiFi Connection for Original JLR DoIP VCI

Original Jaguar Land Rover diagnostic tool JLR DoIP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting.

Procedure:

Connect JLR DoIP VCI W-F interface with vehicle

Connect the other end of VCI with laptop via USB cable

jlr-doip-vci-sdd-1

Open VCI Manager (JLR), press Connect

jlr-doip-vci-sdd-2

Choose Network Setup tab->Wired Etherent

jlr-doip-vci-sdd-3
Tick Enable Wired Etherent Interface

jlr-doip-vci-sdd-4

Press Apply button and Yes

jlr-doip-vci-sdd-5

Then disconnect USB connection
Close VCI Manager
Open VCI Manager again
Press Connect
Go to Network Setup->Wired Etherent
Press Set Factory Default

jlr-doip-vci-sdd-6

Press OK if system prompts you are about to reset the VCI communication settings to a factory default state.

jlr-doip-vci-sdd-7

Enable network connection
Press Set Factory Default again

jlr-doip-vci-sdd-8

In Wireless (802.11), choose Obtain an IP address automatically, then press Access Point

jlr-doip-vci-sdd-9
Choose Wireless resource which is the same as the your network
Press Configure

jlr-doip-vci-sdd-10
Enter wireless security password (encryption key)

Press Next

jlr-doip-vci-sdd-11

JLR VCI is configured to connect to your network
Disconnect and then Connect VCI

jlr-doip-vci-sdd-12

It shows WiFi connection is done
Open JLR SDD software on desktop

jlr-doip-vci-sdd-13

Press Connect

jlr-doip-vci-sdd-14

Now you can run SDD software for diagnosis

jlr-doip-vci-sdd-15 jlr-doip-vci-sdd-16 jlr-doip-vci-sdd-17 jlr-doip-vci-sdd-18

Possible to get Piwis 3 program work with Piwis interface tester 2

This answer for the question whether Piwis 3 diagnostic program can work with Piwis interface tester II

It may be an interesting subject, I’m sure there is some information about this out here.
The Piwis 2 interface is a lot more robust piece of equipment, compared to the cheesy and flimsy looking and feeling interface produced by Actia for Piwis 3.
Originally designed for the VW ODIS system,  the VAS 6154 VCI is quite the service needy piece. [Breaks easily] not a hard comparison to make.
Porsche went cheap on this VCI for Piwis 3. [my humble opinion, way below Porsche standard!]

There is a service from Poland and Ukraine [If I remember correctly] that can make the Samtec based Piwis 2 VCI,  to work with Piwis 3, unfortunately their charges are just as much and frankly cost prohibitive as the New Piwis 3 VCI.  2-3-4 thousand  dollars for these VCIs is simply not reasonable for small  operators. They will come down in price just like the Chinese VCIs did for all manufacturers as the markets get saturated and folks are not buying them as eagerly as in the beginning of the Piwis 3 phad.
They will get as much money as the market bares. [as much as people are willing to pay]

Your more pointed answers will not come in this tread Ibi.
This is CarsFan’s money making tread, he will not volunteer any information, but if U start your own tread, U may be more likely to find out stuff.

Regards, Albert.

p.s. links

Porsche piwis 2 china clone:

https://www.obd2tool.com/goods-4779-Porsche+Piwis+Tester+II+with+CF30+Laptop+or+Lenovo+E49AL+Laptop.html

Vxdiag Prosche piwis 3:

https://www.obd2tool.com/goods-10074-VXDIAG-VCX-DoIP-Porsche-Tester-Piwis-III-with-Lenovo-T440P-Laptop.html

porsche-piwis-tester-iii-download-1 porsche-piwis-tester-iii-download-2 porsche-piwis-tester-iii-download-3 porsche-piwis-tester-iii-download-4 porsche-piwis-tester-iii-download-5