Super Dprog5 IMMO Odometer Airbag Reset OBD Tool Car List

Posted on March 20, 2018 by wp-admin

Super Dprog5 IMMO Odometer Airbag Reset Tool 3 in 1 for BMW Benz and VAG vehicles is new arrival product,can replace Data Smart 3+.Perform instrument calibration, security immo key match, airbag repair and other functions.Perform instrument calibration, security immo key match, airbag repair and other functions.Can realize self-diagnosis function, can automatically identify and diagnose system faults.Support ISO9141, CANBUS, and J1850 protocols.And here we will share Mileage Correction Super Dprog5 IMMO Odometer Airbag Reset OBD Tool Car List.

IMMO

Odometer car list

Airbag

Ford / Mazda software features:

OBD2 key match (no need password), for CAN models.
Roewe (550/350) Software: OBD2 key match (no need password).
Pentium (B50 / B70) Software: OBD2 key match (no need password)

Immo coverage:
all BMW CAS (including CAS3-9S12XDP512) programming.
Odometer adjustmenet coverage:

-all M35080 instruments (incl.M35080 V6), no need dismantle for adjustment;
BMW transmission OBD setting; E38/ E39/ E46/ E53 instrument, EWS/ LCM and EWS4 adjustment.
-Mercedes-Benz ignition module adjustment (912/ 9S12 series ignition module don’t need to disassemble CPU), W211/ W203/ W164 and before year 2000 OBD adjustment. Support Mercedes-Benz Gateway (CGW) adjustment.
-Volkswagen / Audi / Chrysler / GM / Ford / Chevrolet / Jaguar / Lincoln / Opel / Skoda / Seat and Honda odometer adjustment.
Such as: A4 OBD2 kilometers adjustment). And support kilometers adjustment for A6L / Q7 / A8L / R8 / S8 / TT and Volkswagen /
Magotan / Phaeton / Sagitar / Golf 6 / Kaidi / Touran / Touareg / Passat / Bora / Polo / Jetta / Beatles from 2009.

MCU calibration coverage:

Audi / VW Gateway module calibration,
EDC15 / EDC16 engine calibration.

Airbag reset coverage:

Volkswagen / Audi / Mercedes-Benz / BMW / Sail / Opel / Ford / General Airbag reset.
EDC15 / EDC16 / MED9 series engine computer read and write (car modification).
Volkswagen / Audi / Mercedes-Benz / BMW / Sail / Opel / Ford / GM Airbag reset.
EDC15 / EDC16 / MED9 series engine OBD2 read and write (car modification).
The 4th VW IMMO software coverage:

NEC + 24C08 software
NEC + 24C64 software
NEC + 24C32 software
NEC + 95320 software
Micronas (CDC) software
9s12xhz512 (1M80F) software
PASSAT 2012 (NEC+24C64) software
The 4th Audi IMMO software:
A6L/ Q7 software
A3 / TT/ R8 software
A1 software

DSP3 Mileage Correction RADIO CODE READER

Posted on February 10, 2018 by wp-admin

Click the ‘RADIO’ button on the main reader window,select make and model, window, you can see then read radio code.

PROGRAMMER
The programmer function of DSP3 Mileage Correction is powerful; you can use it to do what you want. Click the ‘PROG.’ button on the main window, you will enter the programmer window. Establish a new file or open an old file, select adapter and chip device, then you can fulfill all the operations of ‘edit’, ‘erase’, ‘read’, ‘write’, ‘copy’, and ‘save’ etc.

PROGRAMMER
The programmer function of Dataspecialist PLUS is powerful; you can use it to do what you want. Click the ‘PROG.’ button on the main window, you will enter the programmer window. Establish a new file or open an old file, select adapter and chip device, then you can fulfill all the operations of ‘edit’, ‘erase’, ‘read’, ‘write’, ‘copy’, and ‘save’ etc.

How to Update Yanhua Digimaster3

Posted on September 21, 2017 by wp-admin

Yanhua Digimaster 3 Upgrade instruction: support upgrate online

Step 1, plug the power supply to digimaster3 and insert the
network cable into the LAN interface of digimaster3 at Obd2tool.com.

Step 2, select “Management”

Step 3, select “Update”

Step 4, select “Software Upgrade”

Step 5, the machine is upgrading

Touch screen calibration:
When the touch screen shows not correctly, you can calibrate
it, please refer to the following instructions.
Step 1, select “Stylus Proofreading”

Step 2: use touch pen point at the center of cursor

How to Solve Digimaster 3 WhiteBlack Screen of Death

Posted on September 20, 2017 by wp-admin

Recently some forum bros talked about their death screen (white or black screen of death) of their Digimaster 3. And now, we technicians offers some solutions.

First, please try to update your kernel

Then, try the following solution if white or black screen of death still appears on your Digimaster iii after you have updated the kernel.
1. Remove SD card from D3 to cardreader,and connect to PC. After successful connection, click “Removable Disk(E:)” as showed in the picture.

2. Delete the old file “YHTech” which is in the SD card.
3. Copy the “YHTech” files from CD, and save it in SD card.
4. Please insert SD card into car diagnostic scanner Digimater3 after successfully copy and paste. Then connect to
network and turn on Digimaster 3, click “OK” for downloading when appear remark of “Please connect network download hypervisors!” in the interface.It can be functioned after successful download.

Mercedes Benz audio decoding using Digimaster III

Posted on September 19, 2017 by wp-admin

When the vehicle audio was power off because of battery damage, the audio will start the anti-theft system automatically-Obd2tool.com remind you.

Digimaster III can calculate the audio code out or initialize it, as the following picture shows, Digimaster 3 Odometer Correction has the function of ” Audio decoding” , after click it, you will find it supports decoding audio for Alfa, Audi, Benz, BMW, Ford, gm, Honda, Lexus, mazda, Mitsubishi, Peugeot, Porsche, Renault, Toyota, Volvo, Volkswagen and more.

2. Audio Code Management
Step 1: Select Benz to decode, and de-solder the corresponding chip according to the software prompts. Click “Next” to begin decoding.
Mercedes Benz audio decoding

Step 2: remember the code in the pop-up dialogue box, click “Next”, the code was written in the chip.

Step 3: Solder the chip back to the board, and then use this new code to decode the audio.

3 Address Code
These models only need to short-circuit some welding spot to reset the code, the software will give a specific method.

Digimaster 3 Connector Instruction

Posted on September 18, 2017 by wp-admin

DigiMaster III from OBD2TOOL is multi-functional Automobile data adjusting equipment. It bases on a high performance hardware platform which takes high-speed CPLD and the ARM11 processor as the core device. It is with 7 inch LCD touch-screen.

Attention: All Digimaster 3 has already been registered before shipped out. So no need to register again. Customer who want buy digimaster 3 please do have basic knowleage about chip desoldering.

Techinical question about DIGIMASTER III, please check our techinical service which is next to the description.

Description:

Digimaster III Features

1. It contains a high performance hardware platform which takes high-speed CPLD and the ARM11 processor as the core technology
2. It works with various types of adapter you can easily achieve odometer correction, Audio decoding, airbag resetting, engine ECU resetting, IMMO, programming key for Benz &BMW etc
3. It contains the advanced technology of programming new keys for BMW and Benz, CAS-BDM reading/writing and resetting; 35080V6 erasure etc. large numbers of pictures and particular description makes your operation pleasant

Digimaster 3 Connector Instruction

http://www.obd2tool.com/goods-3261-Digimaster+3+Digimaster+III+Original+Odometer+Correction+Master+with+1180+Tokens.html

Ford Mondeo odometer correction with digiprog 3

Posted on August 13, 2015 by wp-admin

Digiprog 3 V4.94 odometer correction tool will change tachometer mileage in many ways, by OBD2, dismantle dashboard, dissemble chip etc. Here introduces 2 methods of Ford Mondeo mileage correction with DP3. If you fail to correct mileage by OBD2, then try another way around.

Ford Mondeo 24C**
Ford Mondeo HCS 12

Ford Mondeo 2007 24C16

Plug: ST01

Dismantle Tacho

Identify Chip 24C16
Desolder Chip 24C16
Clean Chip 24C16

Set Plug ST01 cable on Chip
Red cable on pin 1
Pin 1 bottom left

Choose vehicle in digiprog iii
PKW/LKW—Ford-Mondeo-2007-24C16
Data Backup/Data restore
Data Back up EEPROM
Chip type
Read data
Write data

Or Data restore EEPROM
Load data
Write

Connect replace tacho
Choose vehicle program
Enter KM value and confirm entry
Programming operation completed
Ford Mondeo odometer correction with digiprog 3

Ford Mondeo odometer correction with digiprog 3

Ford Mondeo odometer correction with digiprog 3
Ford Mondeo HCS 12

Plug 48

Dismantle Tachometer
Dissemble Tachometer
Identify Processor
As shown solder the colored cables of Plug 48 to the suitable points

Connect DigiProg to separate electricity supply
Urgently necessarily
Connect DigiProg3 with the plug
Follow the instruction of the digiprog III v4.94
Choose program: PKW/LKW-Ford-Modeo-HCS12
Save and load data (same procedure as 1st instruction)
Ford Mondeo odometer correction with digiprog 3

Ford Mondeo odometer correction with digiprog 3

How to fix Citroen Picasso 2009 BSI flash problem using DP3

Posted on June 24, 2015 by wp-admin

Car information:

Citroën Picasso 2009 with BSI and 95128 eeprom / Johnson Controls.

Mileage Tool to use:

Digiprog 3 (DP3)

Spend $179

http://www.obd2tool.com/goods-1754-Hotest+Digiprog+III+Digiprog+3+Odometer+Programmer+with+Full+Software.html

best-quality-yanhua-v494-digiprog3-1

Error description:

DigiProg 3 has done writing the new km value by “flashing” by OBDII “reading, verifying, writing” but only until 99 %.

Now car is “dead”, no functions anymore.

Need to tell also that i forgot to put extra battery charger, so this was happen when voltage dropped and now car is “dead”

Re-write with DP3 is possible apparently, recognize BSI number (but NOT the VIN) and does automatically pick-up the saved

“flash-file” and will try to recover, BUT DP3 don’t flash anymore when arrived @ 99%….

EEprom data looks okay

Put all FF in eeprom also don’t wake up the car.

Reference number on label:

PSA = 96 640 590 8002

V 05.01

281201930C

N805243015

boot 28120836-4

hard 28119248-3 C

BSI 04 EV K04 – 00 020309

bsi

Finally solved after all I managed to “repair” it as follow:

Please firstly look at the flash dump “BSI_JC_FLASH_M00″

https://mega.co.nz/#%21RdZAAKbA%2116LeW9udnGH_2cw-o9jqx96fdjSpb3QuELZKo2JaOs4

full of area’s with “00″, so its corrupted in my opinion.

Each time DP3 will try to restore, also as commanded in the log-file, the original flash.
But for some reason DP3 take all time the “BSI_JC_FLASH_M00” and stops at 99%.

In the MCC card/storage there is some other 992 kbyte flash with name “BSI_JC_FLASH_01″ which is the +/- SAME as “JCI_BSI_678A”

“JCI_BSI_678A”: https://mega.co.nz/#!McRTjJgL!fp94IF-fvasqpGlQYAH8h16pM9wIZ6PqUeRcj0Nyv7U

This flash is the real original flash, and the “…M00″ is the modified flash.

Now the trick is : change the name from the “01″ flash into “M00″ and the “M00″ into “01″.
Then DP3 will AGAIN try restore the flash with of course “M00″, but this time the content is the good one because i “misleaded” DP3 by changing file-names

And indeed, this time until 100%, car start and you only need to re-do the whole procedure “read, verify, write” BUT THIS TIME WITH AN EXTRA BATTERY CHARGER .

Hope this will help some members with the same problem.