XHORSE KEY TOOL MAX PLUS AUTEL IM508 ADD SMART KEY TO NISSAN NOTE 2019

In this post, you will learn how to add a new smart key on 2019 Nissan Note by Key tool Max and Autel IM508 key programmer.

What you need:
Nissan Note 2019
Nissan Note working key
VVDI smart remote
Xhorse VVDI key tool Max
Autel MaxiIM IM508 auto key programmer

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-1

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-2

Main steps:
1.Generate ID46 chip with Key tool Max:
2.Add new smart key with Autel IM508:

Go ahead…

1.Generate ID46 chip with Key tool Max:

Put battery into this VVDI smart remote and plug it into key tool max coil

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-3

Select Vehicle remote-> Nissan-> Note-> Note (2013-2016) KeylessGo ID46 433M4433.92MHz FSK
Part number: TWB1G662
FCCID: CWTWB1G744
Then press Generate remote

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-4
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-5
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-6
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-7
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-8

If it failed to generate, check whether the key put well firstly

And pay attention to the caused reasons:
1.If used wire-key, keep the battery with disconnected and make sure the wire be ok.
2.If used wireless key, please insert battery and place the key into left coil.

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-9
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-10

Put the smart remote correct side on coil antenna, and then it can generate

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-11

It will take a little time to write smart remote…

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-12

Burn success

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-13

2.Add new smart key with Autel IM508:

Connect Autel IM508 to the vehicle
Run MaxiIM application
Select IMMO-> Nissan-> System Selection-> Auto detect Type

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-14
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-15

Follow the prompt on the screen to turn on the hazard warning light and open and close the driver door once.
Scanning vehicle system… (This step will take some minutes, please keep patient)
Select IMMO Status Scan

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-16

Smart key and 4 digits authorizations code support
Press IMMO Matching-> All smart key lost

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-17
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-18

Set the vehicle as the following status and the press [OK]
-Ignition switch or power switch: LOCK
-Hazard switch: ON (for preventing BCM from entering into CAN communication sleep mode)
-P (A/T) or neutral (M/T)
-Battery voltage: More than 12V
-Steering: Turn on and turn off the cab door once, Not in fully locked
Then go to next procedure.
Pay attention to the prompt:
“This procedure erases all registered key ID. Therefore, all of the customer’s keys should be obtained before starting this procedure. Do you want to continue?”
Click [YES] to continue
Then you will hear steering lock release sound…
Press push-button ignition switch for 2 seconds or more and turn ignition switch to the ON position
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-19

Follow the procedures on the screen to operate one by one

XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-20
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-21
XHORSE-KEY-TOOL-MAX-PLUS-AUTEL-IM508-ADD-SMART-KEY-TO-NISSAN-NOTE-2019-22

Program smart key success

Finally, test all the remotes function