Gm mdi scan tool software installation well with laptop ready to use

If you ready to buy GM MDI diagnostic tool and feel it is difficult to install software.  this is a good news for you .we  can  install the gm mdi software well for you.  when you received the  goods, you can use it directly . save money and time.  we also provide technology  support . best aftermarket service

after  you received the GM MDI Scan Tool. you need to connect it with vehicles. following picture show you how to connect with vehicles.

11

12

this gm mdi not need battery. When you use it, connect this device with your car, car will provide the power for this GM MDI. And use it to diagnose and code the car.

GM MDI software including GlobalTIS, opeltis, gds2, techwin etc. see in the pictures

13

if you buy the GM MDI Plus EVG7 together. we will install the software well, when you use this device again, it will prompt the hardware is low, you need to update, then just click update is ok.

GM MDI support multi-language. it is convince for you.

14

Gm MDI support GM cars 1990-2013, support Opel model before 2013 year , Holden around 2010 and more vehicles.

gm mdi is work better than gm tech2 diagnostic tool. GM MDI is newer scanner for new GM models, while Tech2 scan tool is for old models.

GM MDI Scan tool Plus EVG7 Tablet PC V2017.02 Software

http://www.obd2tool.com/blog/2017/05/27/gm-mdi-scan-tool-software-installation-well-with-laptop-ready-to-use/

Launch X431 diagun IV VS launch x431 diagun III

Launch x431 diagun IV as newest launch scanner, it is more batter than launch x431 diagun III

  1. Launch x431 diagun iV add Special Function: Brake Reset,Oil Reset,SAS Reset,BAT.Reset,Bleeding,Elec.TH Tottle Rottle Rlrn, TPMS Reset, DPF REG.
  2. launch x431 diagun IV SD Card storage: 16GB, big capacity, which can meet all your requirements,  launch x431 diagun III only 1 GB
  3. Launch x431 diagun IV is is android 7, launch x431 diagun iii is WIN CE 5.0 ,
  1. processor :  launch x431 diagun IV is Quad core 1.1 GHz   launch x431 diagun 3 is 400MHZ ARM9
  2. Battery:launch x431 diagun IV is 2500mh rechargeable polymer lithium battery  launch x431 diagun III 3800 mAh
  3. Funtion:  launc h x431 diagun IV support many functions such as Function Full-diagnosis, Oil Reset Service,Steering Angle Calibration,Electronic Parking Brake Reset,Battery Register / Battery Maintenance,ABS Bleeding,Electronic Throttle Position Reset / Learn,Diesel Particulate Filter (DPF) Regeneration,Tire Pressure Monitor System Reset and more.

Launch x431 diagun iii support : Full diagnosis (Read/erase DTCs, display live data stream etc)

How FVDI and AVDI Commander read and write data from MED17 EDC17?

Please pay attention before you use FVDI and AVDI Commander :
1. Only FVDI and AVDI Commander can read and write data from MED17 EDC17 engine control unit and calculate 6 digit security byte.
2. New VW Magotan, Passat, CC engine type is MED17.5.XX . It is impossible to read out these models’ 7 digit security byte by only reading out data from comfort module, then it’s impossible to make new keys when all key lost and module programming.
3. VAG 18.0 or Newer version of FVDI commander can get 6-digit security byte and 5 digit login password by reading the data from MEDC 17 and get 7 digit security byte by reading data from comfort modules.
4. About connections, you have to prepare these tools:
PC, FVDI /AVDI, USB Cable, MEDC17 adapter, dongle, welding iron , solders , several 1K ohm resisters and 12V DC power supply.

Now we can begin to work:
1. From Picture 1 shows connections between AVDI FVDI ABRITES Commander , PC , Dongle , MEDC 17 adapter. Your PC has to

connect with network.

2. Step by Step to operate
Step 1: Disassemble MEDC17 ECU, and then uncover it;
Step 2: Connect MEDC17 ECU under instructions;
Step 3. Connect FVDI with PC, Open VAG V21 and select special functions and select ” EDC17/MED17 Engine Control Unit”. It

is shown as Picture 2.

3. Select correct MCU type and click ” CONNECT ” as Picture 3.

4. Read what you want to read.

5. Assemble MEDC17 ECU and install it to vehicle.

How to correct Benz W221 odometer with FVDI ABRITES Commander

Here is the detail instruction on odometer correction for Mercedes Benz S-class (W221) and CL(W216) vehicle models with OBDⅡFVDI ABRITES Commander for Mercedes Benz diagnosis.

Backup important files

Open Special Function “CGW (ZGW) Explorer” to read the EEPROM and the flash memories of Central Gateway (CGW) control.  Back up EEPROM and the flash dumps as files in your hardware.

FVDI ABRITES will automatically back up EEPROM and the flash memories file when it reads them. The backup files should be installed on C:/Program Files/ABRITES software for IDXXXXXX/Mercedes.

Select vehicle model, like S-class W221

Select EEPROM, click Read EEPROM and save it to a file after EEPROM has been read.

Select Flash and click Read Flash and save it to a file after FLASH has been read.

2.Modify ASSYST and ASSYST PLUS service history records
Open Special Function “ASSYST PLUS”. Select the ZGW type “W221”. Click “Get Current” button to see the internal data that is stored inside ASSYST PLUS module.

Click “ASSYST PLUS Service Memory” to view different service history. Enter “Main Odometer”, “Operating Time (Days)” and “Number of Oil Changes” to alter all this information.  Click “Yes” when FVDI ABRITES program asks to set the information for the different service history records. Enter detail for each record.
For example: If your vehicle has 3 records, you need to enter the details for 3 service intervals. The values for the day cycle counter should be entered in an increasing way. Here is the record example. You can verify them as you wish.

3.Change the main Odometer in Dashboard, EZS & CGW
Next you should change the odometer in Instrument Cluster as well as in EZS and CGW module.
Open “Odometer Correction” special function and select vehicle as S-class W221. Then click “Get Odometer” button.

Select “Set Odometer” to load EEPROM and Flash dumps
NOTE: Make sure the ignition is ON when click “Set Odometer” button.

3.Change the odometer in other devices
Select Electronic Parking Brake/Regenerative Braking System to change the odometer in this module.

Select Tire Pressure Monitor in FVID ABRITES menu to change the odometer id this module.

You can open the “Actual Values” windows and check the stored Messages and Activation values. If you want to change these values, click Activation Tests button. Three options are available, click “Start Test” button after choose one.

Select Vehicle Power Supply Control Module and click the “Activator tests” button from the drop-down box. Then open the Actual Values windows and check the displayed odometer values.

Select Electrical Seat Adjustment Driver and click “Activator tests” button. Then click “Output Tests” button from drop-down box to check the displayed odometer values. If you see the value that unavailable, ignore it. .

Select Electric Seat Adjustment Front Passenger and do previous setting
Select Diesel Engine Control Unit and do previous setting

5.Clear DTCs
Erase all error codes that may have been stored in ECU control modules
NOTE: Leave only the setting “CAN UDS” and “CAN KWP 2000” protocols setting when clearing error codes which will make the procedure faster.

 

see more click www.obd2tool.com

2016 FVDI 2 ABRITES Commander V24 For VAG VW Audi Seat Skoda

FVDI2 ABRITES Commander = FVDI V2016 FULL Version + FLY OBD Terminator FULL Version + J2534 DrewTech Software

FVDI 2 ABRITES Commander For VAG VW Audi Seat Skoda highlights:

1. Multi-languages: English, Germany, Spanish, French, Russian, Italian, Danish, Czech, Chinese, Bulgarian

2. Newest version: V24

3. FVDI 2 Update: For customers who bought old FVDI Commander from us before, you can send the FVDI Commander hardware and soft-dongle bakc to us and pay 300.00USD extra, we will replace the FVDI 2 for you,
with same car model software+ free FLY OBD Terminator software + all J2534 DrewTech Softwares.
PS: (if you lose the soft-dongle, you need pay another 90.00USD, if you have both hardware and soft-dongle, you just need pay 300.00USD)

4. Buy FVDI2 VAG, You Can Get Hyundai/Kia/Tag Key Tool Software by default

5. You can choose DAF or Bikes software for free as well

6. Package come with Free OBD Termination software, function including:
-1. VAG-VW, Audi, Seat, Skoda immobilizer Generation 4
-2. VAG-VW, Audi, Seat, Skoda immobilizer Generation 5
-3. AUDI A6/Q7 immobilizer Generation 4,5

7. Package come with Free J2534 Softwares:
-1. Honda HDS V3.016 +
-2. JLR SDD V145.00 +
-3. TIS V11.00.017 +
-4. VCM IDS +

8. Package cancel USB Dongle, dongle has been setup inside the ABRITES Commander Hardware, more convenient.

Hyundai & Kia GDS VCI “CRC Error” fixed

GDS VCI for Hyundai and KIA diagnostic system “CRC Error” solution is provided.

Problem:
Installing Hyundai GDS (Global Diagnostic System) software on Win 7 laptop, when come to Hyundai master setup wizard installation step, the system reported an error:

“CRC error: The file C:/gvci/ocx/install/dotnetfx-eng.exe doesn’t match the file in the setup’s.cab file. The medium from which you are running the setup may be corrupted; contact your software vendor.”

Error screen
22-1

Possible reason:
1. Operating system issue
2. Improper installation steps
3. Software damaged

Solution:
Please follow the video or blog guide (below) to install GDS program from OBD2TOOL. If the Hyundai master setup can be well installed, but others cannot, then send the specific file name that cannot be installed to obd365 customer service. We will resend the file.

We recommend users to choose U-Disk format software rather than CD software. U-Disk format GDS V2.14 software HDD is easier to install.

volvo truck scanner 88890300 Vocom Interface with software installed on laptop ready to use

Volvo 88890300 truck diagnostic tool is the latest OEM diagnostic tool made by Vocom and designed for maintenance of Volvo trucks, buses and other heavy vehicles that covers the whole repair process through the use of plug-ins..

If you don’t know how to install the volvo 88890300 Vocom Interface software, we can help you  do it, you only need to buy it with laptop.  it is convince and save time . the Software version is  PTT1.12/2.40 , this software must installed on Windows XP system computer. Support Multi-languages.

Installation:
OS (system): XP
Mainly 2 steps to install:
Install the software contained in the CD; it will take 1-2 hours
Connect the network connection to download from the server to install, it will take 2-3 hours.

What Companies and electrical systems Volvo 88890300 Vocom works with?
Volvo Trucks (Older electrical system, Vehicle electronics ’98, V2, V3, V4);
Volvo Buses (Conventional, Multiplexed, Multiplexed v2, Multiplexed v3);
Volvo Construction Equipment;
Volvo Penta (VERSION2);